Neodym Technologies - MiniKnowz Part No. Generator

GAS DETECTION SYSTEMS FOR SAFE ENERGY

Toll-free - 1-877-723-5400

  Home

  About Neodym

  Contact Neodym

  Investor Information

  Part Number Generators
    - Knowz™
    - KnowzNet™ Panel
    - KnowzNet™ Sensors
    - MicroKnowz™
    • MiniKnowz™
    - ProtiSen™
    - HydroKnowz™
    - Panterra
    - PowerKnowz™

  Products

  Order Online

  Press Releases

  Privacy Policy

  Site Map

  Technical Support

  Terms of Use

M i n i K n o w z ™

M i n i K n o w z ™

Combustible gas sensor modules ("Janus").

$74 to $120 - Hydrogen/methane/propane

(Add to cart via part number generator)

Product Links

> Features
> Details
> Specifications
> Datasheet (PDF)
> Ordering options
> Part No. Generator
> Gallery

Related Links

> Eval. Kits
> PK-Port™ (PDF)
> Product Matrix

PART NUMBER GENERATOR

The most commonly selected options have been checked as defaults. If your preferred configuration is not selectable below, then please contact Neodym.

Target Gas

Hydrogen Methane Propane

Alarm Concentation (PPM)

PPM Recommended alarm concentrations:

Hydrogen: 4000 to 10000 (10% to 25% LEL)	Propane: 2100 to 5250 (10% to 25% LEL)

Methane: 5000 to 12500 (10% to 25% LEL)

Warning Level (Percent of Alarm Level)

   Percent (20 to 80, 0=no Warning Level)

Output Signal Type and Action

   0-5 VDC (0.5V offset, 200 steps of 20 mV each, one step per resolution unit)
   Step Function (Discrete voltages for Normal, Warning, Alarm & Error)
   TTL, Normally-High, Auto (self-clearing)
   TTL, Normally-Low, Auto (self-clearing)
   TTL, Normally-High, Latching (pushbutton/power-cycle reset)
   TTL, Normally-Low, Latching (pushbutton/power-cycle reset)

        If TTL output, signal is triggered by: Warning State and/or Alarm State

Output Signal Hysteresis

  Hysteresis for Hydrogen & Methane: 2000 PPM, for Propane: 1000 PPM

   No hysteresis     Apply hysteresis

Error Handling

If sensor fails or operating temperature is out of bounds, signal this:

   Visually/error state only     by activating alarm devices(s) (fail safe)

Overexposure Handling

If sensor is subject to overexposure damage, handle this by:

   setting maximum sensitivity     by setting persistent error condition (fail safe)

Input Power Supply

   4.75 - 5.25 VDC     7 - 40 VDC     7 - 60 VDC

Interface connector type

Hirose DF3 series (2mm)
Molex Micro-Fit Jr. (3mm)

Interface harness

   Include Hirose/Molex 15cm color-coded wire interface harness

MiniKnowz™ PART NUMBER FIELDS

	MN	Gx	Annnx	Wnnx	On	Hn	En	Xn	In	Kn	Jn
Field:	-1-	-2-	--3--	--4--	-5-	-6-	-7-	-8-	-9-	-10-	-11-

1: MiniKnowz™ product family identifier

2: Target Gas. X = H(ydrogen), M(ethane) & P(ropane)

3: Alarm Level. nnn = concentration code. (code = Alarm PPM / resolution units)

     Alarm Action. x: A = trigger nothing. B = trigger TTL.

4: Warning Level. nn = percentage of alarm concentration. No warning state if nn = 0

     Warning Action. x: A = trigger nothing. B = trigger TTL.

5: Output Signal Type.

     1=TTL n-hi-auto. 2=TTL n-lo-auto. 3=TTL n-hi-latch. 4=TTL n-lo-latch. 5=0-5V. 6=Step

6: Hysteresis. 0 = none. 1 = Apply.

7: Error Handling. 1 = Visual/error state. 2 = Errors trigger alarm.

8: Overexposure Response. 1 = Hypersensitivity mode. 2 = Trigger persistent error

9: Input Power Supply. 1 = 5VDC. 2 = 7-40VDC. 3 = 7-60VDC.

10: Connector. 1 = Hirose DF3 2mm. 2 = Molex Micro-Fit Jr. 3mm.

11: Interface harness. 0 = none. 1 = Hirose harness. 2 = Molex harness